Four-panel skirt: step-by-step manufacturing instructions for beginners

Starting with a four-panel skirt is a great project to take on if you’re new to sewing and want something enjoyable and fulfilling. This skirt is a great addition to your wardrobe because of its straightforward yet fashionable design. Moreover, you can dress it up or down based on the fabric you select.

You will be guided through every stage of the procedure by this guide, from choosing your supplies to putting the finishing touches on it. Despite your lack of experience sewing skirts, you’ll find the instructions to be simple to follow. You’ll have a gorgeous, handcrafted skirt at the end that you can be happy with.

It’s okay if you’re a novice. You can learn the techniques required to make this beautiful piece with a little perseverance and focus on detail. Now let’s get started and create your own four-panel skirt!

Step	Description
1	Measure your waist and hips, then decide on the length of your skirt.
2	Cut four identical fabric panels based on your measurements, adding extra for seams.
3	Pin the panels together, right sides facing, and sew the side seams.
4	Hem the bottom edge of the skirt by folding and sewing it neatly.
5	Attach an elastic waistband or a zipper, depending on your preference.
6	Iron the seams flat, then try on the skirt to check the fit.

Features of choice

A four-panel skirt can be sewn on elastic, buttons, or a belt.

The purpose of the product must be taken into account when determining the skirt’s length. We sew a mid-length skirt for a business suit; mini and midi length skirts are also options for daily wear. Maxi lengths go well with light beach models and elegant skirts.

The purpose of the skirt also influences the fabric and pattern selection. Furthermore, keep in mind that fabrics with horizontal stripes are not advised for overweight women because they elongate the silhouette. It’s best for larger women to sew skirts with the strips oriented at an angle. Such a master class is discussed in the article.

You can make one-of-a-kind products with the addition of the model with pockets, a coquet, and overhead valves.

Building a pattern of the skirt of the four -clinky, cutting and sewing technology

There are two ways to wear the fourklink skirt. It can be four identical wedges, the pattern for which is built in an entirely different algorithm, or it can be different wedges for the front and rear panels, modeled on the basis of a straight skirt pattern. We’ll think about both approaches to creating patterns.

With side seams

Think about producing a pattern for the 48th size.

Every construction in the straight skirt drawing will be made by us.

We take out 3 cm from the side seams and 1 cm from the center seams on both panels along the waist line.

Elevate the side seam’s upper point by one centimeter.

Constructing the waist’s finger joints.

The dart solution is 2 cm on the front panel and 3 cm on the back.

Divide the distance in half between the middle and side seams to determine the dart’s axis, then mark the location. Reduce the perpendicular’s height. We reserve the designated size of the dart solution starting at this point along the waist line. The dart’s length is 10 cm for the front panel and 12 cm for the back panel. By joining the indicated points with curved curves, we build the darts.

We extend the panels along the bottom edge, forming a 2 cm flare on each side.

We build the seam lines on the sides.

Skirt without darts

You can create a flared skirt pattern without the need for darts by using this pattern. Cut the pattern along a vertical line that is drawn through the center of each dart to accomplish this. We close the darts by pulling the lower panels apart. Next, we use smooth lines to match the shapes of the skirt’s upper and lower edges.

How much fabric is needed

When cutting, the consumption will be equal to the length of the skirt plus an additional 7–8 cm for cuffs and allowances if a 1.4 m wide material is used.

Should the fabric’s width be between 0.7 and 0.8 meters, the consumption will be equivalent to two skirt lengths plus an additional 14 to 16 centimeters for hems and allowances.

An illustration of a pattern layout on 0.7 m wide fabric is shown in the drawing below.

Please take note that the patterns’ dotted lines must match the fabric’s grain.

Remember to allow 1 centimeter for the top edges, 2 centimeters for vertical seams, and 4-5 centimeters for the bottom edge when cutting.

How to sew a skirt

For those who are new to sewing, here is a quick rundown of the steps involved:

• we transfer the contours of the parts to the bottom layer of material using snares (basting stitches) or chalk;
• sew down the central seams;
• grind down the darts (if any);
• perform side seams.

Consider the coincidence of the control marks for the waist, hips, and lower edge when sewing vertical seams.

From the waist to the bottom edge, or top to bottom, is how vertical seams are sewn.

The left side seam is then stitched with a zipper. Ironed allowances are made for vertical seams.

After sewing the belt on, hem the product’s lower edge.

Without side seams

The following model has two side wedges and one central wedge in the front and back.

For such four-wedges, darts placed in these places, in place of side seams, guarantee the fit along the side lines.

As in the previous instance, the straight skirt pattern serves as the foundation for pattern construction.

We made an 11 cm allowance to the right of the middle line based on the layout of the back panel. Draw a straight vertical line. We take a measurement 3 cm to the left of the waist line. We enlarge the piece by 4 cm along the lower edge. We draw the lines for the vertical seams in the center back panel using the points that we have obtained.

We made a 12 cm allowance to the left of the middle line based on the front panel’s pattern. Draw a straight vertical line. We measure 3 cm along the line drawn from the waist. We enlarge the section by 4 cm along the bottom edge. We draw the lines of the central front panel’s vertical seams using the points that we have obtained.

In order to construct the side panel, take 3 cm off the bottom edge in both directions and from each side along the waist line. We construct vertical seam lines. We construct a dart along the center line (= virtual side seam line). Its solution is 5 cm, and we measure the depth by taking a measurement 6 cm up from the hip line. Elevate the dart’s upper points by one centimeter above the waist.

Determine the centers of the lengths between the side darts and the vertical seams, then mark the points. We sketch down straight vertical lines. We deduct 0.75 cm in each direction from these lines, which are the darts’ middle lines. The darts are 8 centimeters long. For the waist and waist darts, we construct pattern lines.

Draw a smooth line for the bottom cut and raise the lower edge by 1 centimeter at the side seams.

How much fabric do you need?

When cutting a material with a width of 1.3–1.5 meters, the consumption will be the same as the length of the skirt plus an additional 6–8 centimeters for hems and allowances.

The consumption will be equivalent to two skirt lengths plus an additional 12 cm for cuffs and allowances if the width of the fabric used is between 0.8 and 0.9 meters.

An illustration of a pattern layout on 0.8 m wide fabric is shown in the drawing below. Cut out the central panels first.

Mark the side wedges after that. In this instance, the vertical side seam line and the grain line should align.

Remember to account for the allowances when cutting: 1 cm for the top edges, 2 cm for the vertical seams, and 4-5 cm for the bottom edge.

The same sewing technique used on the previous model is used on this skirt.

Constructing a wedge pattern

This is the easiest way to create a hand-made pattern for a four-wedge model.

Measurements will be required:

• waist circumference – OT;
• hip circumference – OB;
• length from waist to hips – Dtb;
• length of the product – DI.

There is a vertical line drawn in the format’s center. We mark point A by taking two to three steps back from the top edge. We draw a horizontal line through it.

Determine the size by using AA1 = AA2 = 1⁄8 OT. Set aside this amount and label points A1 and A2 on either side of point A.

We set the measurement value Dtb aside and move vertically down from point A. It usually equates to 16–18 cm, roughly. Make note of point C.

Mark point B and measure down DI along the same vertical line.

Mark the hip line and the bottom line by drawing perpendiculars through points C and B.

Place aside, along the hip line, the value determined by the formula ΡΡ1 = ΡΡ2 = 1⁄8 (OB + 2 cm). Insert C1 and C2 points.

To construct the wedge’s side contours, draw straight lines through points A1, C1, A2, and C2. Draw straight lines all the way to the bottom. Place points B1 and B2 where they meet the bottom line.

Measure down 15 mm from point A and mark point A3 to design the waist line. Join points A1, A3, and A2 using a template for a concave curve.

Align the wedge’s lower edge next. To accomplish this, measure the length of the A3B segment and set aside an equivalent amount along the wedge’s side lines. A2B5 + A1B4 = A3B. Concave curves should be used to connect points B4, B, and B5.

The pattern for the wedge is prepared. Don’t forget to account for allowances when cutting: 1 cm at the waist, 1.5–2.0 cm along vertical seams, and 1.5–2.0 cm (min).

Let’s now examine how to make these skirt models by hand.

Long skirt

The four-panel skirt pattern is made for the following European sizes: 36, 38, 40, 42, and 44.

The product is 106 centimeters long.

The model’s waist is designed to be low. The top border sits 15 mm below the natural waist.

In order to create a skirt, you must first:

• chiffon with embroidery: for a width of 1 m, you need 4.5 m;
• linen, knitwear: for a width of 1.4 m, you need 3.0; 3.1; 3.2; 3.3; 3.4 m;
• concealed zipper 22 cm long;
• threads, sewing tool.

Description

We create a full-size four-panel skirt pattern based on the suggested drawing.

V1.01 of LEAD Technologies Inc.

We draw a line of the shared thread on the completed pattern. We mark the middle of the wedge and fold the pattern in half to accomplish this.

We draw a 3 cm wide facing along the waist. To obtain a pattern for processing the cuts of two wedges at once, we duplicate it onto a different sheet and reflect it in a mirror image. We mark the contours, lay out the patterns on the fabric, and leave 15 mm of space around the edge.

We have to stop using chiffon.

• gore – 4 pcs.;
• facing – 2 pieces with a fold.

From the fabric that lines the inside:

• gore (according to the main pattern, but shorter by 1 cm along the bottom edge) – 4 pieces.

Important note

A lining must be made in duplicate for the facing pieces.

Stitch the vertical seams on the right, front, and back for the full length of the gores. Mark a 20 cm section on the left side seam that will be used to sew in the zipper.

For the lining material pieces, repeat the process.

Smooth out all the allowances.

Attach the lining to the skirt’s main portion and sew the lower edges.

Trim the margin to 7-8 mm. Don’t smooth the edge.

With the wrong sides of the skirt and lining folded together, baste along the top left cut edge.

Beginning with the back panel, stitch in the zipper. Sew the skirt and petticoat’s left side seam. At the conclusion of the cut, we make the allowances. We stitch the lining and skirt together along the top edges.

Sew the facing’s right side seam. Work with the facing to process the product’s upper edge. Sew the facing to the petticoat, making sure to include the zipper allowances. The long skirt is prepared!

Four-panel skirt made of linen: video master class

A four-panel skirt is an easy-to-understand but satisfying sewing project that’s great for beginners. This post will walk you through every stage of making a skirt, from selecting the appropriate fabric to cutting, sewing, and finishing it. Even if you’re new to sewing, you can confidently make a stylish, custom-fit skirt with our easy-to-follow instructions and helpful tips.

Skirt made of fabric with a diagonal pattern

Before sewing, you must get ready:

• fabric;
• hidden zipper;
• button, snap or hook;
• threads, sewing tool.

Description and photo master class

We’ll need measurements in order to build the pattern:

• waist circumference;
• hip circumference;
• length from waist to hips;
• length of the product.

As previously mentioned, we use our hands to create a wedge pattern.

Furthermore, we must create a blank for the belt. Its width is 8 cm (in finished form 3 cm), and its length is OT + 5 cm. You could also make belt loops to wear as an ornamental belt. You must cut out blanks for them in this situation.

The pattern is applied to the fabric at an angle to its stripes. Use pins to secure. We sketch the wedge’s shape onto the fabric. In two locations on the pattern (see photo), we apply it by drawing markings.

This is done to make sure that the stripes match at the seams and to account for the pattern stripes’ direction in the final product.

To indicate the next wedge, move the pattern.

Here, what’s important to notice is how the stripes on the pattern match the real pattern on the fabric.

Two wedges have already been marked. You must flip the pattern’s striped marking to the other side in order to mark the remaining wedges. You can accomplish this by gently pressing them or copying them to the light. Next, we sketch lines on the pattern’s reverse side.

We thus obtain a mirror image of the wedge pattern.

We apply the pattern to the fabric with its reverse side facing up, observing how the stripes line up with the design.

We mark its contours and secure it with pins.

We use the same markings for the fourth wedge.

We give allowances of 1.5–2.0 cm for side seams, 1.0–1.5 cm for waist cuts, and 3 cm for lower cuts.

Eliminate the specifics. The wedges can be pinned or basted. Ensure that the pattern’s stripes line up at the same time. Repeat the basting if required.

Next, use the machine to stitch the vertical seams. Make sure to leave a space for sewing the zipper along the back seam. Iron out and process the allowances using an overlock.

Incorporate a concealed zipper into the back’s middle seam.

Stitch the ends of the belt blank after folding it in half with the right side facing inside. After cutting the corner allowances, remove the belt. Iron the specifics.

In case you want to create belt loops, cut the stripes, sew them together, and finish them.

You can choose to stitch the detail.

We provide a brief master class with illustrations on how to carry out this stitching procedure in more detail.

Use a pin to secure the belt loop in place. These are typically the locations of the virtual darts in the skirt’s front and back.

The belt is pinned on top the incorrect way around.

Reposition the belt and press the seam. After calculating its length to match the belt’s width, turn the other end of the belt loop and iron it.

Close the stitching seam by flipping the belt to the opposite side and basting it.

Stitch into or adjacent to the stitching seam. Use a pin to secure the belt loop’s second end.

Sew along the edge to secure the belt loop’s top.

Sew a button onto the belt after creating a loop.

Turn the product’s bottom edge and hem it or stitch it with your hands using a blind stitch.

For those who are new to sewing, creating a four-panel skirt is a satisfying project. You can make a chic and customized piece that fits well and expresses your style by following these easy steps.

Recall that practice makes perfect. If it’s not perfect the first time, don’t worry. You develop new abilities and boost your self-assurance in your sewing skills with each project.

You’ll discover methods to incorporate your individual touches as you become more accustomed to the process, making each skirt genuinely one-of-a-kind. Continue trying new things and relish the creative process.

Video on the topic

Constructing a pattern for a straight skirt – step-by-step instructions

Pattern of a four-piece skirt in 5 minutes!

How to sew a wedge skirt? Constructing a pattern for a wedge skirt

Constructing a drawing of a straight skirt. Lesson No. 6.

Four-piece skirt in 10 minutes – eternal classic. Design, cutting and fitting in one video.

Skirt pattern | Step-by-step instructions on how to make a skirt pattern